1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

tC specs

Discussion in 'Scion' started by Undrstm8ed™, May 8, 2008.

  1. Undrstm8ed™

    Undrstm8ed™ New Member

    Start a Conversation
    Joined:
    May 6, 2008
    Messages:
    19
    Likes Received:
    1
    tC


    Chassis Code:: ANT10
    Engine Code:: 2AZ-FE

    Colors available::
    - Azure Pearl / Paint code# 8Q6 05/07
    - Black Cherry Pearl / Paint code# 3P2 05/07
    - Black Sand Pearl / Paint code# 209 05/08
    - Classic Silver Metallic / Paint code# 1F7 06/08
    - Flint Mica / Paint code# 1E0 04/068
    - Indigo Ink Pearl / Paint code# 8P4 05/-
    - Nautical Blue Pearl / Paint code# 8S6 06/08
    - Silver Streak Mica / Paint code# 1E7 05/-
    - Sizzling Crimson Mica / Paint code# 3R0 08/-
    - Super White / Paint code# 040 04/08
    - Waveline Pearl / Paint code# 857 08/-

    Release series Colors::
    - RS1 Absolutely Red / Paint code# 3P0 (05) limited to 2500
    - RS2 Blitz Blue mica / Paint code# 8Q1 (06) limited to 2600
    - RS3 Blizzard Pearl / Paint code# 070 (07) limited to 2500

    ENGINE
    - Type 2AZ-FE 2.4-liter, 4-cylinder, DOHC 16-valve EFI with VVT-i, aluminum alloy block and head
    - Bore and Stroke 88.5 x 96.0 mm
    - Displacement 2.362 cc
    - Compression Ratio 9.8:1
    - Valve Train 4-valve/cylinder with VVT-i
    - Horsepower (SAE)** 161 hp @ 6,000 RPM
    - Torque** 162 lb.-ft. @ 4,000 RPM
    - Ignition System Toyota Direct Ignition (TDI)
    - Fuel System Multi-point EFI
    - EFI Recommended Fuel 87-octane unleaded
    - Emission Control ULEV
    - Coefficient of Drag 0.32

    POWERTRAIN
    - Drive System Type Front-wheel
    - Ratios: 5-speed manual
    1st 3.538
    2nd 2.045
    3rd 1.333
    4th 0.972
    5th 0.775
    - Reverse 3.583
    - Differential Ratio 4.235

    - Ratios: 4-speed ECT automatic
    1st 3.943
    2nd 2.197
    3rd 1.413
    4th 1.020
    - Reverse 3.145
    - Differential Ratio 2.740

    SUSPENSION
    - Front Independent MacPherson strut
    - Rear Independent double wishbone
    - Independent double wishbone
    - Stabilizer Bar Diameter (front/rear) manual : 0.83/ 0.71, auto: 0.83/ 0.79 inches (manual : 21/ 18, auto: 21/ 20 mm )

    BRAKES
    - Front Ventilated disc
    - Front Diameter 10.83 inches
    - Rear Solid disc
    - Diameter 10.59 inches
    - Parking Center hand brake

    STEERING
    - Type Power-assisted rack-and-pinion
    - Ratio 17.7
    - Turns (lock to lock) 3.145
    - Turning Circle 36.1 feet

    TIRES AND WHEELS
    - Wheel Size 17 x 7.0 inches / 16 x 6.5 inches
    - Type and Material Aluminum alloy Steel with wheel covers
    - Tire Size P215/45Z R17 / P205/55 R16
    - Tire Type All-season steel belted radial
    - Spare Temporary T125/70 D17

    CAPACITIES
    - Engine Oil 4.3 quarts (4.5 liters)
    - Fuel Tank 14.5 gallons
    - Cooling System 6.4 / 6.3 quarts (manual/auto) (6.8 / 6.7 liters)

    EXTERIOR DIMENSIONS (inches)
    - Wheelbase 106.3
    - Overall Length 174.0
    - Overall Width 69.1
    - Overall Height 55.7
    - Tread Width (front/rear) 59.3/59.3
    - Minimum Ground Clearance 5.2 (Two passengers / no cargo)

    INTERIOR DIMENSIONS (inches)
    - Headroom (front/rear) 37.6/36.6
    - Legroom (front/rear) 41.6/33.6
    - Shoulder Room (front/rear) 54.3/50.0
    - Hip Room (front/rear) 53.2/47.3
    - EPA Passenger Volume 84.7 cubic feet
    - EPA Cargo Volume 12.8 cubic feet
    - Seating Capacity 5
    - EPA ESTIMATED FUEL ECONOMY (mpg) 5M 22/29 4-ECT 23/30

    VEHICLE MASS (lbs)
    - Curb Weight 5M 2,901 4-ECT 2,965

    ESTIMATED PERFORMANCE
    - Zero to 60 mph: ? - ? sec (Man/Auto)
    - Zero to 100 mph: ? - ? sec sec (Man/Auto)
    - Standing 1/4-mile: ? - ? sec sec (Man/Auto)
    - Top speed (governor limited): ? mph (? whether Calif. model only)

    SAFETY FEATURES
    - Standard driver and front passenger airbags
    - SRS Standard driver’s knee airbags
    - Available front seat-mounted side airbags and front and rear side curtain airbags
    - SRS Headrests in all seating positions
    - First-aid kit
    - Three-point front seatbelts with pretensioners and force limiters;
    - ALR/ELR retractors on all passenger seatbelts, three-point rear outboard and center seatbelts
    - Anti-lock Brake System (ABS) with Electronic Brake Distribution (EBD)
    - CRS top tether anchor brackets and lower anchor latches

    BASIC LIMITED WARRANTY COVERAGE
    - 3-year/36,000-mile Comprehensive
    - 5-year/60,000-mile Powertrain
    - 5-year/unlimited-mileage Corrosion Perforation
     
    #1
  2. Undrstm8ed™

    Undrstm8ed™ New Member

    Start a Conversation
    Joined:
    May 6, 2008
    Messages:
    19
    Likes Received:
    1
    awww.dezod.com_prod_images_large_emamage_ultimate1.jpg

    * (Dip) Toggle Switch - 2 independent setting can now be stored and accessed via the Toggle Switch. 2 separate maps for the Injection Adjustment Map and the Ignition Map. (For Rotary engines, 2 separate Primary and Secondary Injector Maps and Leading & Trailing Ignition Maps.) i.e. one program for street and one for race track.
    * Serial port - External data (like GReddy Warning Meters, and other future optional products) can be monitored and recorded in real time through a data link cable.
    * Switch Port - Data logging and Ignition Cut features can be activated with the use of an optional Remote Switching System and Switching Harness
    * Option 1 & Option 2 - An additional Option Connector is added to the previous Pressure Connector. Now any two Options (like GReddy Pressure Sensor, GReddy Temp Sensor, Multi-Switching System, A/F Meter, Auxiliary Switch, Factory Pressure Sensor, or Other Analog Input signal) can be selected using the Option 1 and/or Option 2 ports.
    * USB Port - e-Manage is industry first to adapt the USB communication technology. We have improved communication with ability to use standard USB cables. This improvement also enhances the communication speed for more detailed real time monitoring and data recording.

    Real Panel

    * Because of new Features, there are now 3 Harness Connectors (sold separately). The 18-pin and 12-pin connectors and the signal pins are identical to the previous e-manage system, while a new 14-pin connector was added for new features. Additional Vehicle Specific Plug-in Harness may also be available for certain applications.

    Circuit Board

    * Many Optional Adapters, which previously need to be purchased separately, are now built-in. The internal circuit board contains 20 Jumper Switches to accommodate (previously separate) features, including:
    * Mazda Hotwire Airflow Meter Adapter
    * Ignition Signal Adapter Socket (Ignition Signal Adapter 1 & 2)

    Parameter Setting - The biggest change to this system is in the Parameter Setting window. With all the added features, the window is now in a tab menu format.

    * Speed Limiter Cut Feature - This feature will eliminate the factory speed limiter. (May not work on some vehicles)
    * Throttle Setting - Any voltage can be inputted directly to set the throttle position.
    * Warning Setting - e-manage Ultimate can illuminate the Active L.E.D. as a warning light for RPM and/or one additional parameter from the menu, by selecting and setting a warning point value (or an unused I/J CH can be used to activate a relay to illuminate an external warning light).
    * Ignition Cut Feature - With the installation of a switch (in the ON position), ignition can be cut at a set RPM point
    * Map Trace
    * Protect Feature - Each Map has the option to be password protected
    * A/T Shift Compensation Feature - On vehicles with Automatic Transmissions, ignition timing can be compensated at set shift-up and shift-down points
    * Channel Change Feature - Vehicles with a distributor type ignition system may able to use group fire or individual ignition systems (Replacement parts and modifications to the wire harness is required)Also, Group injection systems may be changed to sequential injection (Modifications to the wire harness is required).

    Map(s)

    * Airflow Output Map - Previously labeled Airflow Adjustment Map is now Airflow Output Map. (#)This can now used to eliminate the factory airflow meter. This is done by directly inputting voltage or frequency in to this map.
    * Anti Engine Stall Feature - The 8 adjustment cells are now upgraded to 16 cells, for even finer adjustment.
    * Injection Adjustment Map - Fuel trimming in the previous system was achieved by adjusting the Airflow Adjustment Map which could also affect the ignition timing. The improved Injection Adjustment Map is used to trim and add fuel directly by controlling the injector signal, therefor it will not affect the ignition timing at all. (However with an internal jumper setting change, the system is still able to trim the fuel by adjusting the airflow signal like the previous unit)
    * Acceleration Injection Map - Like the Injection Adjustment Map, the Acceleration Injection Map¬ can trim fuel by controlling the injector signal. This is used if it is necessary to smooth rapid transitions to wide open throttle.
    * Individual Cylinder Injection Adj. & Individual Cylinder Ignition Adj. Maps - It is possible to correct uneven combustion between cylinders, by fine tuning each individual cylinder for more advanced tuning.
    * Vehicle Speed Correction Map - Inconsistencies due to differences in vehicle speed (difference in load) can be corrected with this map.
    * Coolant Temp Correction Map (Must be Selected with Knock Signal 1) - When the ECU Coolant Temp Calibration does not match the e-manages tuning, this map is used to tune the system at various temperature ranges.
    * Intake Air Temp Correction Map (Must be Selected with Knock Signal 2) - When the ECU Intake Air Temp Calibration does not match the e-manages tuning, this map is used to tune the system at various temperature ranges. (#)This map is also be used when eliminating the airflow meter on a vehicle equipped with a hotwire type airflow meter.
    * Rev Limiter Cut - For vehicles with a fuel cutting controlled rev limiter, this feature will drive the injectors past the factory rev limiter. *This feature will not work on vehicles with rev limiter controlled by ignition cut.
    * A/F Target Value Map (feedback tuning function) - By inputting target Air Fuel values in this map, e-mange Ultimate will automatically make corrections to the Injection Map, if an A/F meter (*high quality) is connected to the Auxiliary Output signal. This feature can shorten the tuning time.
    * Ignition Adjustment Map - The Ignition Adjustment Map can accurately advance ignition timing by controlling the crank angle/cam angle signal.
    * Acceleration Ignition Map - Ignition timing can also be corrected for a rapid change in the throttle opening rate for a smoother transition into wide open throttle.
    * NVCS Control Map - NVCS (Nissan Valve Control System) can be controlled with out the need for NVCS Adapter 1.
    * Analog Output Map - This feature can be used to eliminate the factory boost cut function on vehicles that are equipped with both an airflow meter and a pressure sensor (i.e.: FC3S, Subaru). Also, on some vehicles, the factory feedback range can be adjusted by outputting a corrected throttle position signal.
    * Auxiliary Output Map - The fixed 4x4 map on the previous unit is now a fully adjustable 16x16 map. Set your own "ON" and "OFF" conditions.
    * Idle Stabilization Map - If the factory idle control valve is a solenoid type valve, this map can vary the valves duration to adjust the injection rate. (#)This is used when eliminating the airflow meter.

    Other Added Features

    * RPM Signal Recognition Improved RPM signal. If the standard RPM signal wire cannot be used, an RPM signal can be recognized though a crank angle / cam angle signal. With an internal jumper setting, the system can even recognize RPM from the negative signal of the ignition coil.
    * Fouled Plug Feature - When initiated this feature can help clean fouled spark plugs by cutting the injectors firing at start up. To fix the fouled plug start the engine with wide-open throttle.

    Data Log Features

    * Data Logging - Samplings can be recorded at 20msec on up to different 8 channels on the unit itself and over 30 when using the included software. The data can be recorded even when the PC is not connected.
    * TEXT File Feature - The data recorded in the Real Time Display mode can now be save as TEXT file. Organizing the data can simplified by opening the data in Excel and creating a graph.
    * Knock Monitor (Future update) - Knock can be monitored and reviewed.
    * Ignition Timing Display (Future update) - Ignition Timing can be monitored in the Real Time Display mode.
    awww.dezod.com_prod_images_large_emamage_ultimate1.jpg
     
    #2
  3. Undrstm8ed™

    Undrstm8ed™ New Member

    Start a Conversation
    Joined:
    May 6, 2008
    Messages:
    19
    Likes Received:
    1
    E-Manage is an inexpensive programmable fuel management system that allows you to properly tune your factory fuel system without changing the entire factory ECU system to a "stand-alone" unit. The E-Manage system is a "piggy-back" type unit that will save you from wiring headaches by working in conjunction with factory ECU.

    This system will allow the tuner to easily control the pulse duration of factory injectors or upgraded injectors with a built in adjustable dial, It also has a built-in VTEC* controller which can adjust the VTEC* shift point as well as the fuel curve. An optional communication software package (PC Windows) and harness kit is available to fine tune the entire engine, from 16 additional fuel RPM points, ignition timing, larger injectors, airflow meters, injector duty cycle, and control up to 2 sub injectors, with the use of optional communication software and a PC Window based lap-top, the E-manage system will assist the tuner in data logging and real time monitoring capability

    [​IMG]

    05/07 Scion tC, Greddy E-Manage (blue Box) settings
     
    #3
  4. Undrstm8ed™

    Undrstm8ed™ New Member

    Start a Conversation
    Joined:
    May 6, 2008
    Messages:
    19
    Likes Received:
    1
    WARNING::

    This material is offered free of charge and stated from the Scion tC service manual repair manual. However, Scion, Toyota, JDMchat.com or its affiliates is NOT RESPONSIBLE for your actions. Use of this information comes under extreme caution for your own safety. Please exercise caution when servicing electrical on your vehicle. Always test the wires with a meter and if your not comfortable with this kind of work. PLEASE seek qualified help before causing temporary or permanent damage of your vehicle. We cant stress that enough. Use at YOUR own risk...

    05/06 tC ECU pin outs
     
    #4
  5. Undrstm8ed™

    Undrstm8ed™ New Member

    Start a Conversation
    Joined:
    May 6, 2008
    Messages:
    19
    Likes Received:
    1
    WARNING::

    This material is offered free of charge and stated from the Scion tC service manual repair manual. However, Scion, Toyota, JDMchat.com or its affiliates is NOT RESPONSIBLE for your actions. Use of this information comes under extreme caution for your own safety. Please exercise caution when servicing electrical on your vehicle. Always test the wires with a meter and if your not comfortable with this kind of work. PLEASE seek qualified help before causing temporary or permanent damage of your vehicle. We cant stress that enough. Use at YOUR own risk...

    07 tC ECU pin outs
     
    #5
  6. Humveelat

    Humveelat New Member

    Start a Conversation
    Joined:
    Sep 22, 2008
    Messages:
    126
    Likes Received:
    1
    Wow! That pretty awesome for my setup.. How much would it cost mate?
     
    #6
Similar Threads: specs
Forum Title Date
Scion xD specs May 8, 2008
Scion xA specs May 8, 2008
Scion xB specs (2nd gen) May 8, 2008
Scion xB specs (first gen) May 8, 2008

Share This Page